We will check the business route and provide you with a quotation.
Contact us via the product inquiry form.

Please contac us.

Download from here.

Please contac us.

Portable vibration meters are one year after leaving the factory, other measuring instruments are two years after leaving the factory.

The preferred measurement points for condition monitoring are

(1) Areas that are easy to approach.

(2) Locations that are not easily affected by anything other than anomalies.

(3) Locations with high sensitivity to changes in abnormal conditions.

(4) Locations with low signal attenuation or loss due to anomalies.

(5) Locations with good measurement reproducibility.

Please tell us what you need below

1. purpose of measurement (what type of vibration you wish to measure)
2. required display/output
3. desired budget

The Apps are different: Air2 is for tablets, Air2 Light is for smartphones.

You can find out more here.

Not included in the standard configuration.
You can select this as an option or provide your own.

Please check the product page for recommended tablets.
Tablets other than those listed have not been tested and operation cannot be guaranteed.

It can be downloaded free of charge from Google Play.

Enter 'Air2' on the search screen.

The app is free of charge.

No contract with a telecom carrier is required except when downloading.

Approximately 6 hours of continuous use.

*Air2 is a portable device for patrol monitoring.

Approx. 10 m.
However, the distance is largely dependent on the wireless environment of the location where it is used.

The following areas with radio wave certification can be used.
China
South Korea
Taiwan
North America (USA and Canada)
Europe (EU member states, Iceland, Norway, Liechtenstein, Switzerland, Turkey)
The Philippines
Thailand

For overseas purchases, please contact us.

Yes, it is possible.
Stable measurements are possible even in environments where wireless connection is difficult.

*For stable measurements, the optional USB plug bracket is recommended.
*A commercially available USB host cable is required.

There are four main causes

1. tablet (app) malfunction
2. wireless interference
3. low Air2 battery power
4. malfunction of the Air2 itself

We will check the cause. Please contact us.

If the red light keeps blinking repeatedly during USB charging, there is a high possibility of insufficient start-up power due to complete discharge of the built-in battery.

Purchase an eneloop-specific charger and charge the battery.

USB functionality will be restored after charging is complete.

With the optional Data Management Software (DB-2012), measurement data can be centrally managed on a PC.

Standard type has a vibration sensor built into the terminal.

Connector type can be used by wired connection to optional sensors or sensors from other manufacturers.

Yes, please contact your distributor.

*Note: The lid should be removed using a screwdriver and without applying too much force.

The causes are as follows.

・Windows OS is no longer supported. (As of August 2020 Guaranteed operating system: Windows 10)

・Installation has not gone well.

・Booting without the authorisation key (USB memory stick).

If the problem persists, please contact us.

Card Vibro Air2 is only compatible with Android OS.

It does not work on iOS or Windows tablets.

The causes are as follows.

1. USB factors →Is an authorisation USB key plugged in or is the tablet connected as a media device?
2. Environmental factors →PC specifications, security issues, cable and connector issues.
3. Configuration factors →Is the database file opened in the PC software incorrect? The correct database file is 'C:\IMV\DB-2012\Master_cvndb1.db'.

If the problem persists, please contact us.

No other communication is supported except for USB communication.

Please see the function table on the product page.

Please see the list of distributors.

Unfortunately, SmartVibro only saves waveform data.
OA values and FFT data are not supported for storage.

It is not compatible with the replacement of sensor of different models. (Connectors are also different).

The ground is stable and the ground surface is flat.
The depth of the foundation should be at least 30 cm.
Avoid locations where people pass by frequently or are normally exposed to vibrations.

Depends on the type of sensor used.

Turn off the power toggle inside the seismometer.

If using the built-in uninterruptible power supply battery, wait 5-10 minutes.

【SW-54/SW-52ST】

By using the optional Maintenance Software (DS-7274), history and waveform CSV data can be downloaded via serial connection to a PC.

【TM-0013-SW ＆ SW-52ST】

Seismic information is recorded in CSV data on the built-in memory card.

Please check the following.

If none of the problems are found, please contact us using the product inquiry form.

・The SW-54/SW-52ST connector is not firmly inserted.

・The SW-54/SW-52ST is incorrectly wired.

・The slide switch on the main board inside the SW-54/SW-52ST is set to [HOST].

・The optional external display (ED-74) is energised before the SW-54/SW-52ST is energised.

For horizontal accuracy, mount on a flat surface within 5 °.

Cardinal directions need not be a concern, but should be fitted if seismic waveform recording analysis is being considered.

Settings can be changed either by panel operation using a processing unit with touch screen or by PC communication using optional maintenance software.

Printers and PC output using maintenance software are available.

Note: Printer and maintenance software are optional items.

The performance of the seismograph's internal clock is about 6 seconds per day difference.

If the error becomes large, correct it using the touch panel operation.

Automatic correction by inputting a time calibration signal is also possible.

■ Inspections will be carried out at the IMV factory.

● Details
・Inspection/étalonnage/contrôle du fonctionnement/étalonnage dynamique complet après vérification du fonctionnement
・Submission of reports and test results
・Traceability chart/calibration certificate are issued on request
　　　*An official quotation will be provided if repair or replacement of consumable goods are needed.

● Contact/Delivery address

MES Business Division
2-6-10 Takejima, Nishiyodogawa-ku, Osaka, 555-0011, Japan
TEL : +81-6-6471-3155
FAX : +81-6-6471-3158